How to Connect PVC Pipe without Glue? [5 Methods]

Adult erector sets are occasionally associated with PVC pipes. This is due to their ease of assembling and customizing. In addition, they are an extraordinary pipe due to their durability and ability to transport liquids and gases.

The only decision to be made is whether to dismantle them. The pipes will be waterproof if you use PVC glue, but they will be difficult to disassemble again. PVC glue is also messy for permanent use.

If you don’t want to use glue, go to the hardware store and buy PVC pipe fittings found in most locations. Alternatively, you could slice two tiny pieces of duct tape with scissors. Joining PVC pipe without glue is beneficial to seal pipe fitting on both sides of the pipe to ensure a tight fit.

We will demonstrate how to connect PVC pipe without glue in this article. This way, you will avoid encountering the project’s unwieldy side. Continue reading for more hints and tips.

Related: How to Repair PVC Pipe in Tight Spaces? [7 Effective Ways]

Table of Contents

  • What Is PVC Glue?
  • Connecting PVC Pipe without Glue [5 Methods]
    • Method-1: Using O-ring
    • Method-2: Using Mechanical Connectors
    • Method-3: Using RTV Silicone
    • Method 4: Using Flex Couplings
    • Method-5: Using Threaded PVC Pipe
  • Where Is the PVC Pipe Connection Suitable to Use?

What Is PVC Glue?

In general, PVC glue dissolves the surface of the PVC. They used welding to join the two pieces of metal together. A single material cannot be extracted. However large the particle size unless it is reduced to submicron size. For ease of manufacturing, PVC glue is specifically designed to soften the plastic and stick.

PVC glue is different from traditional glue: it doesn’t adhere to surfaces but acts as a bonding agent as well. The PVC glue will absorb away at the pipes’ outer layers, enabling the substances to come together. In addition, it chemically bonds to plastic pipes and fittings for long-term use.

PVC glue or fittings may be used to seal the pipe when using PVC pipe to hold liquids or gases.

It is not always necessary to apply a permanent seal to this form of application. More joints and connections will be needed if you’re constructing a PVC frame. It may be time-consuming and very messy.

Related: How to Replace Cast Iron Drain Pipe with PVC? [3 Easy Steps]

Connecting PVC Pipe without Glue [5 Methods]

Method-1: Using O-ring

These fittings, also known as push-to-connect fittings, are marketed specifically for this purpose. They have an O-ring for waterproofing and a steel ring that crimps onto the inserted PVC pipe.

You can also remove and reuse these fittings using a unique tool supplied by the brands that market them. Do you know how to join PVC pipe without glue by using these fittings?

For doing this, use these steps:

Step 1
Verify that the spigot end has a chamfer of approximately 12° to 15° if cut in the sector. Refer to the Appendix for O-ring joint chamfer measurements and witness mark locations.

Step 2
Clean the socket, paying particular attention to the ring groove. Avoid using a rag that has been soaked in lubricant.

Step 3
When replacing the ‘O’-type rubber rings, before installing the rubber ring, first clean and dry the ring and its groove, as instructed on the box.

Step 4
Run your finger around the rubber ring’s lead-in angle to ensure that you should be careful that it properly seated, not bent, and uniformly distributed throughout the ring groove.

Step 5
Clean the pipe’s spigot end back to the witness mark. Determine that all burs are gone.

Step 6
Lubricate the spigot end back to the witness mark, paying careful attention to the chamfered area.

Step 7
Align the spigot with the socket and force the spigot into the socket with a firm, even thrust. Brace the line’s socket end to prevent previously joined pipes from closing.

Step 8
Make sure the mark is on the joint scarcely visible to the naked eye. A pipe should never be inserted into the socket as far as possible. This will accommodate potential pipe development.

Step 9
If a pipe joint has been homed too far, it can be removed immediately; however, mechanical aids are needed to separate the joint once the lubricant has dried.

Method-2: Using Mechanical Connectors

Mechanical PVC pipe connectors are extremely popular in domestic settings and often provide an excellent balance of low cost and service simplicity. You can do this by following steps:

Step 1
Clean and deburr your pipe with wire wool, preferably to remove any dirt or residue.

Step 2
The small washer/compression nut stack must be opened fully.

Step 3
Reverse the nut, washer, and rubber washer onto the section of pipe to be connected. The rubber washer should be a snug fit and should extend at least 15-20mm beyond the pipe.

Step 4
Slide the joint body onto the pipe, snugging it against the rubber washer.

Step 5
Slide the washer and bolt through the connecting pipe before it made contact with the joint.

Step 6
Do that, and make a secure, watertight connection, then snug the bolt using a plumber’s wrench.

Method-3: Using RTV Silicone

Both piping, openings, joints, and seams must be sealed in PVC. Silicone is a simple and quick method to seal PVC pipe without glue. However, before you can add the silicone, the pipe must be completely dry.

If you don’t seal the PVC pipe well enough, it won’t be waterproof, and water can leak in. To keep it waterproof, buy many tubing and plan the pipe well beforehand. Do you know how to seal PVC pipe without glue just using RTV silicone sealant? If you don’t, then you can follow these steps.

Step 1
To remove dirt and debris from the PVC pipe’s surface, use a damp cloth or rag.

Step 2
With the utility knife, trim 1/4 inch from the tip of a tube of silicone caulk. Then, punctuate the seal with a nail or a thin wire inserted into the tube’s tip.

Step 3
Incorporate the silicone caulk tube into the caulk gun. Push the push plate against the tube’s rim.

Step 4
Press the trigger to force the push plate into the tube of silicone.

Step 5
Determine the seam or gap in a piece of PVC at the joint. Seal the seam or gap by placing the tube’s tip on it.

Step 6
Continue pressing the button until the silicone tip emerges. To add a bead of silicone, slide the tip of the tube along the seam or gap.

Step 7
Wet your finger by dipping it in a bowl of water. Then, smooth the silicone texture by swiping your finger over it.

Method 4: Using Flex Couplings

To connect two PVC pipes, flexible couplings are used. These PVC connectors are available in a variety of configurations to accommodate the necessary dimensions and operating pressure.

Are you excited to know how to connect PVC pipe by using flexible coupling? Then, you can follow these steps for PVC pipe coupling.

Step 1
Trim a section of the sewer with a power pipe cutter or saw. The junction/replacement section should be about 20mm long.

Step 2
Extract the disconnected segment and drop. Any current or power source should have a BAND-SEAL connection point at each end. There is no lubrication required.

Step 3
Using the new pipelining technique, integrate this into the production line. A pencil-mark half the width of the BAND-SEAL width must be attached to each joint.

Step 4
Center a BAND-SEAL over one pencil point, then secure the clamp bands one at a time. Tighten the bands before shear.

Step 5
Put the BAND-SEAL into place and then apply firm pressure to the exposed pipeline for the best results. Next, use bush saws to cut the plastic pipe in half so that you have a square tip on both ends.

Step 6
Both the PVC pipes should have a Band-SEAL mounted. Compress the bushes, so the front edge is parallel to the PLANAR. There are no lubricants needed.

Step 7
Bands should be stretched on one side, followed by shear forces. When installing the BAND-SEAL, tamp around and under the tubing with special care.

Method-5: Using Threaded PVC Pipe

Depending on the application, there are several types of PVC thread options, but the most common uses a small metal circular object with sharp internal threads. Threads are provided with a handle, which is used to sever the yarn for joining PVC pipe physically.

It’s not difficult to thread PEX tubing; you just need a PEX tubing vise, a rag, and a vise grip-type vise. You should follow these steps:

Step 1
Wrap the rag around the PVC pipe in the middle and secure it with the vise.

Step 2
Place the threading tool on the pipe’s edge and turn clockwise while pressing the tool into the pipe until the tool’s edge contacts the pipe’s end.

Step 3
Take the pipe out of the clamp and clean the fresh threads with the cloth.

Where Is the PVC Pipe Connection Suitable to Use?

Outdoor Uses:

The most frequently used plastic piping material is polyvinyl chloride (PVC). It is corrosion-resistant, cost-effective, and long-lasting. It can be used underground or outdoors if the pipe is stabilized and treated with UV inhibitors, and coated with water-based latex paint.

Related:

Best Latex Paint Sprayers

How to Sand Latex Paint?

Uses for Building Infrastructure:

Cross fittings made of PVC pipes are often used when constructing a building framework. Apart from its low installation costs, plastic pipe is desirable for non-pressure applications due to the smooth inner walls, which ensure high gravity flow rates and reduce the likelihood of stoppages. In addition, plastic PVC pipes are strong enough to withstand earth loads and have high chemical resistance, resulting in long service life when used in sewer installations.

Related: How to Remove a Tub Spout That’s Stuck?

Under-ground Sewerage System and Wastewater Disposal:

PVC pipe connectors are designed to be buried in the ground and were used to absorb and evacuate wastewater without using pressure. PVC is a substance that is used in the treatment and management of waste. PVC is used to dispose of debris in various modern society infrastructure components, ranging from households to commercial buildings and manufacturing plants. PVC pipes are used in the sewage and wastewater conveyance systems and drains and vents connected with buildings and machinery.

Related: How to Install a Utility Sink in Garage?

Final Words

Understandably, some people want to use PVC glue. Perhaps they prefer a less lasting solution or are averse to dealing with the resulting mess. Rather than using glue, you can use specialized fittings to secure your PVC pipes in place and allow them to perform their intended function.

You already know that the fittings can prevent leaks. I hope you would know how to secure PVC pipe without glue by reading this article.

Related:

How to Cut Flexible Metal Conduit? [Step by Step Guide]

How to Replace Two Handle Shower Valve? [Pro-Guide]

How to Remove a Jacuzzi Tub?

Leave a Reply

Your email address will not be published.