How to Use a Floor Sander Like A Pro? [Tips & Tricks]

Do you want to learn how to use a floor sander like a pro? This post will show you the basics of using this machine so that you can get started. The following are some tips and tricks for getting the most out of your new machine. Make sure to read on for more information!

Table of Contents

  • 9 Steps for Using A Floor Sander
  • How to Change Sandpaper on a Floor Sander?
  • How Much Sandpaper for the Floor Sander?
  • How Much to Rent a Floor Sander?
  • Floor Sander Safety Tips

9 Steps for Using A Floor Sander

Step 1: Check and Clean Your Floor

Evacuate each household item in your room. On the off chance that the floor is appended to anything, evacuate them. Spread the air vents, lights, windows, and entryways with the goal that they won’t get dusty—tape over each opening, including electrical switches, vent pipes, and different outlets. Seal the room entirely from outside by utilizing concealing tape and plastic sheets. To dispose of the soil from the floor after, vacuum the floor before sanding.

Step 2: Putting on the Grits

First, put your paper on. Take your paper the number facing towards you and bend it. If you want to get pretty precise, calibrate to do the perfect crease on it. Do that on both sides after you finished doing that, flip the drum over with the 7/16 wrench, which will provide you if you need one.

Turn score plate. You can see a dot right there. Now take the other one going in the opposite direction. Turn the other one down. That one is going to be turning out until you see the dot on the other one. Once you got the both dots facing towards you then take your sandpaper, wrap it around itself over.

Make sure you line your edges up and squeeze it in there. Get it all the way wedged and of course your papers you have to work with it a little bit more. It will eventually go once you get that fit in there. Take your wrench and on the left while bringing one quarter down the. The second one over there on the right bring it one quarter. Turn up to make sure you do a complete trying. Roll the paper and check if it is finely rolling or not. Make sure that there is no air pocket in it.

Tip:

If you have an air pocket in your drum, basically what is going to happen is when the sander hits the floor, The floor is going to rip the paper off. Make sure the sandpaper roller is very tight.

Step 3: Lift the Floor Sander

Drum floor sanders, they are clumsy beasts that weigh more than 120 pounds. You are going to require help from some companion to raise that sander ultimately. So ask someone to lift it.

Step 4: Wear Appropriate PPEs for using a drum floor sander

  • Use a Dust Mask
  • Wear a dust mask. While working there will be a lot of dust so if you inhale it, that’s not good for your health.
  • Hearing Protection
  • Use ear protection as it is going to make a loud noise. It can damage your ears. So better be safe than sorry.
  • Wear safety glasses or a face shield to protect your eyes from the dust.

Step 5: Specify the Sanding pattern for the floor sander

The drum floor sander resembles a combination of a vacuum and a garden cutter; however, you can’t move it over the floor in a vacuuming or cutting example. At some random second in time, drum sanders intend to cut a divot into the wood of your level that is 8″ wide by 1/2″ long.

For whatever length of time that the drum keeps on moving over the floor, that cutting zone leaves a pleasant, even swath of smooth floor. Be that as it may, on the off chance that you stop, in any event, for a minute, the drum will leave a profound channel called a ‘stop mark’ on the floor surface.

It implies a drum floor sander is sanding secure just when it is moving in an orderly fashion-forward, or an orderly fashion in reverse. You can’t sand while you are turning or altering course. In this way, to make the minimum number of turns, you sand one portion of the room first, at that point pivot once, and sand the other half.

Step 6: Start sanding at the left wall

It’s time to get your swatches ready and start sanding! I found some great sanding tips that will help you along the way..

You should consistently ensure that the machine is moving before you utilize the feathering handle to bring down the drum to the floor delicately.

Not long before you arrive at the divider, you will lift the drum off the floor, and as you start your converse pass, you will bring down it tenderly back to the level as you pull the machine in reverse over the same way that you simply secured while going ahead.

Step 7: Sand in the Opposite Direction of the Drum Motion

Pull your drum floor  sander, do not push. It implies that it is rotating the sander in something contrary to the drum movement. Try not to endeavor to draw near to slender, entryways, dividers, and different components that won’t sand. You can harm these things using a drum floor sander, maybe with the rotating drum or by hitting zones with an apparatus’s lodging.

Step 8: Sand lightly and carefully

Utilize just the heaviness of the sander while moving the drum floor sander. You don’t need additional weight is required. Follow those grain on the wood, tug the sander in even lines, covering each range how you would while cutting a garden. Stop much of the time with the goal that you can take rest and void the residue pack.

Make sure you read this article so that you can avoid huge mistakes when sanding.

Step 9: End up sanding where you started

Since you will walk in reverse over a similar way that you sanded going ahead, you will get up in the same spot where you started. Tenderly lift your drum off the floor before you grind to a halt.

Presently you have to move the machine more than four inches, with the goal that the following pass you make covers the first pass by at any rate a large portion of the width of the sanding drum.

When your drum is in a new position, rehash the system you utilized for the main pass. tenderly bringing down the drum as you stroll forward. Lift and bring down at the divider where you alter course, and sanding in reverse directly over the way you used to go ahead.

Rehash this up, back, more than four inches design until you have arrived at the right-side divider. Turn the machine around 180 degrees, which will naturally reposition you with a divider to your left side. Presently you sand the other portion of the room similarly as you did the first half, covering the two segments marginally to guarantee a smooth mix.

You have been wondering to know that hardwood floor can be sanded with random orbital sanders. Here’s the 8 steps!

Check out the video below where you will get important tips for using a floor sander.

Editor’s Tips

How to Change Sandpaper on a Floor Sander?

Pull the clip up that releases the sandpaper, and the sandpaper is pre-cut, so it is just the matter of rolling off of the tube is going to stand the drum. Take one end of the roll and flip it in the sheet and start spinning. It doesn’t matter if they are perfectly next to each other.

When you are setting, you can just adjust as you are rolling. Slide the rollover just a little bit. They will come around. In the end, set up the clip in the last piece. Stick the end directly down into that place. You will find a clip. Run the sander just for a couple of minutes. It will tighten it up. It is just a matter of adjusting the drum floor sander, and when you turn the sander on, just let it run for two to three minutes and tighten it and back up.

Hacks!

How Much Sandpaper for the Floor Sander?

Switch your sandpaper consistently – it’s unquestionably something we took in the most challenging way possible. The more now and again you switch the paper, the quicker you’ll have the option to sand the floors.

Try not to think little of the measure of paper you will require, either. While procuring the machine, you purchase the sandpaper, as well; however, as a rule, you can restore any overflow. You would prefer not to get short on paper, particularly in case you’re working at the end of the week and can’t get hold of something else!

For the considerable drum floor sander, use around 12 sheets of 24 coarseness, eight sheets of 40 coarseness paper, eight layers of 80 coarseness paper, and five coats of 120 coarseness paper. For the edging sander, use about a similar measure of each coarseness once more.

How Much to Rent a Floor Sander?

DRUM SANDER requires a $150.00 – you have to deposit it first.

If you want to rent it for four hours minimum, they will charge $48 and per week at least $272.

And if you’re going to rent it for four weeks per day, they will charge $68, and all total in four weeks will cost $816.

Floor Sander Safety Tips

Wellbeing initially ought to consistently be at the bleeding edge of your brain when utilizing a drum floor sander. Below are the most important safety procedures you should follow when using the drum floor sander:

1. Never Get Complacent

One of the most significant suggestions to recall is that you ought to never get careless around a force device.

Regardless of how acclimated you find a good pace drum floor sander, taking care of the machine with the right degree of regard will help guarantee you never lose a finger.

The risk territory around your run of the mill massive drum floor sander is inside four creeps of the sander bit.

It implies you have to focus while working the sander.

You should move gradually utilizing an appropriate position where you are in no peril of slipping or losing your equalization.

Ensure there are no interruptions, for example, the danger of your pet canine out of nowhere, hopping up anxious for a walk.

Try not to get self-satisfied. Be cautious while you work.

2. Know When to Rest

Even though similarly as with work, you should offer yourself an adequate reprieve each hour or two, we’re discussing the machine.

Your instrument ought to give a rest between employments so that there is no threat of over warming.

3. Avoid Extension Cords

Utilize just the appended electrical string or additional lines that permits per producer’s guidelines. A drum floor sander draws such a lot of intensity that it is conceivable to liquefy an inappropriately estimated other range, bringing about an electrical fire.

4. Treat Your Floor Sander’s Power with Careful

Some home improvement instruments like paintbrushes and air pocket levels are sheltered and favorable. Different apparatuses like table saws and powder-impelled nailers are so ground-breaking and equipped for causing annihilation and personal injury that they don’t merit anything, not precisely the most extreme consideration and regard.

Final Words

Hardwood floors are sturdy and hold warmth, in contrast to different sorts of the deck. A drum floor sander is an integral asset with replaceable rough sheets that sand wood ground surface to a smooth, astonishing completion.

Leave a Reply

Your email address will not be published.